1. DO NOT leave light connected to a power source when not in use.
2. DO NOT place light face down on ANY surface. If the light is switched on the intense heat generated may ignite the surface
and cause a meltdown of the lamp body.
3. Ensure all electrical connectors are secure - loose connections will generate excessive heat, damage wiring and cause
electrical failure.
4. The outer lens should be washed clean with copious amounts of water and a clean sponge. Wiping it with a dry rag will
scratchthelens,especiallyifthesurfaceisdusty.NEVERcleanthelightwithcleaninguidorsolvent.
5.DONOTattempttocleantheinsideofthelightortouchtheinsidelensandreector.
6.LIGHTFORCElightsarenotdesignedtobeusedforlongperiodsoftimeinastationarypositionwithminimalairow,failureto
comply will void warranty. Contact LIGHTFORCE direct to discuss alternative options such as reducing globe wattage.
7.GLOBEREPLACEMENT:TheXenophot®globegivesapproximately10%greaterefciencythananyotherhalogenglobeof
similar wattage. A number of optional globe strengths are available upon request. For removal, simply:
a)Rotatethereectorhousinganti-clockwisetodisengageit.
b)Removeoldglobebygrippingrmlyandpullingoutinthelongaxisdirectionoftheglobe.
i) DO NOT TOUCH NEW GLOBE WITH FINGERS, use a tissue or plastic sleeve. Prior to inserting a new globe, scrape the
globelegswithanabrasivesurface(sandpaperorknifeedge)toensurepositivecontactwiththeglobeholdercontacts.
ii)Positiontheglobelegsrmlyintothexedcontactsoftheglobeholder,applyingarmpressuretowardstherear.AVOID
jerkingortwistingmovements.NOTE:GlobecanonlybemovedtotheleftandrightNOTupanddown.
iii)Mereplacementoftheglobeintotheglobeholderisoftennotsufcienttogiveaproperlyne-tunedbeam.Theoperator
canovercomethisbyaligningthesplitlinealongthetopoftherotationlockingNIBandthesplitlineontheendofthe
handlewiththecentreoftheglobelament.(seeFig.1)
iv) All other globes should be seated against the globe holder with little or no air gap.
v) Maximum globe wattage recommendation:
140 LANCE: 12V 75W
170 STRIKER: 12V 100W
240 BLITZ: 12V 100W
Note: USING GREATER WATTAGE WILL VOID WARRANTY
8. FOCUSING MECHANISM: The patented focus mechanism allows precise adjustment of the beam to various concentration
patternsasdesired.SimplyrotatethereectorandselectthedesiredSPOT.
9. DIMMER CONTROLLER FUNCTION:
Please see line drawing on next page
• The dimmer product is polarity sensitive (see line drawing)
• On/Off switch – This switch turns the light on and off. To turn light off, press and hold the on/off button for at least 0.5
seconds.
• Aquickpressoftheon/offswitchforlessthan0.5secondswhilethelightisonwillincreasethebrightnesstofull.
• Increasing Intensity Level – Press and hold this button will increase the intensity of the light.
• Decreasing Intensity Level – Press and hold this button will decrease the intensity of the light.
LIGHTFORCEAUSTRALIAPTYL
TD•28OrsmondStreet,HindmarshSA5007Australia•www
.lightforce.com|email:
[email protected]
Australia:Tel:0884400888|Fax:0883460504•Int’l:Tel:+61884400888|Fax:+61883460504
AlllogosandimagesaresubjecttorelevanttrademarkandcopyrightprotectionLIGHTFORCEPtyLtd|©Jan2011•Dataandspecicationscontainedmaybesubjecttochangewithoutnotice.
LIGHTFORCEAUSTRALIAPty.Ltd.,shallbenotbeliablefordamage,malfunction,failureresultingfromaccident,misuse,misapplication,unauthorisedrepair,neglect,modication,unauthorisedornonstandardreplacementparts,accessories,
globes,batteriesorvoltageortheoperationoftheProductbeyonditstechnicalandenvironmentalspecications.
INSTRUCTION DATA
PRODUCT: SL Handheld Variable
VER: 1.1
DATE: JAN 2012
Fig.2
Fig.1
Kommentare zu diesen Handbüchern