Lightforce NEW ENFORCER HALOGEN STANDARD Bedienungsanleitung PDF herunterladen

1. DO NOT leave light connected to a power source when not in use.

2. DO NOT place light face down on ANY surface. If the light is switched on the intense heat generated

may ignite the surface and cause a meltdown of the lamp body.

3. Ensure all electrical connectors are secure - loose connections will generate excessive heat, damage

wiring and cause electrical failure.

4. The outer lens should be washed clean with copious amounts of water and a clean sponge. Wiping

it with a dry rag will scratch the lens, especially if the surface is dusty. NEVER clean the light with

 cleaninguidorsolvent.

5.DONOTattempttocleantheinsideofthelightortouchtheinsidelensandreector.

6. LIGHTFORCE lights are not designed to be used for long periods of time in a stationary position

 withminimalairow,failuretocomplywillvoidwarranty.ContactLIGHTFORCEdirecttodiscuss

alternative options such as reducing globe wattage.

7.GLOBEREPLACEMENT:TheXenophot®globegivesapproximately10%greaterefciencythan 

any other halogen globe of similar wattage. A number of optional globe strengths are available upon

request. For removal, simply:

a)Rotatethereectorhousinganti-clockwisetodisengageit.

b)Removeoldglobebygrippingrmlyandpullingoutinthelongaxisdirectionoftheglobe.

i) DO NOT TOUCH NEW GLOBE WITH FINGERS, use a tissue or plastic sleeve. Prior to inserting a new

 globe,scrapetheglobelegswithanabrasivesurface(sandpaperorknifeedge)toensurepositive

contact with the globe holder contacts.

ii)Positiontheglobelegsrmlyintothexedcontactsoftheglobeholder,applyingarmpressure

 towardstherear.AVOIDjerkingortwistingmovements.NOTE:Globecanonlybemovedtotheleft

and right NOT up and down.

iii)Mereplacementoftheglobeintotheglobeholderisoftennotsufcienttogiveaproperlyne- 

tuned beam. The operator can overcome this by aligning the split line along the top of the rotation

 lockingNIBandthesplitlineontheendofthehandlewiththecentreoftheglobelament.(see

Fig.1)

Fig.1

iv) All other globes should be seated against the globe holder with little or no air gap.

v) Maximum globe wattage recommendation:

EF140** : 12V 75W

EF170** : 12V 100W

EF240** : 12V 100W

Note: USING GREATER WATTAGE WILL VOID WARRANTY

Handheld Enforcer Halogen Instructions

LIGHTFORCEAUSTRALIAPTYLTD•28OrsmondStreet,HindmarshSA5007Australia•www.lightforce.com|email:[email protected]

Australia:Tel:0884400888|Fax:0883460504•Int’l:Tel:+61884400888|Fax:+61883460504

LIGHTFORCEAustraliaPtyLtdshallnotbeliablefordamage,malfunction,failureresultingfromaccident,misuse,misapplication,unauthorisedrepair,neglect,modication,unauthorisedornonstandardreplacementparts,

accessories,bulbs,batteriesorvoltageoroperationoftheproductbeyonditstechnicalandorenvironmentalspecication.

INSTRUCTION DATA

PRODUCT: ENFORCER HALOGEN

VER: 1.0

DATE: MAY 2014

1 2

INSTRUCTION DATA 1

Inhaltsverzeichnis

Seite 1 - INSTRUCTION DATA

1. DO NOT leave light connected to a power source when not in use.2. DO NOT place light face down on ANY surface. If the light is switched on the inte

Seite 2

8.FOCUSINGMECHANISM:Thepatentedfocusmechanismallowspreciseadjustmentofthebeamto variousconcentrationpatternsasdesired.Simplyrota

Kommentare zu diesen Handbüchern

Keine Kommentare

Lightforce NEW ENFORCER HALOGEN STANDARD Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Beleuchtung Lightforce NEW ENFORCER HALOGEN STANDARD herunter. Lightforce NEW ENFORCER HALOGEN STANDARD User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Beleuchtung Lightforce NEW ENFORCER HALOGEN STANDARD