Lightforce 240 BLITZ REMOTE MOUNT DL Bedienungsanleitung PDF herunterladen

1. Ensure all electrical connectors are secure; loose connections will generate excessive heat, damage wiring and causing

electrical failure.

2. The outer lens should be washed clean with copious amounts of water and a clean sponge. Wiping it with a dry rag will

 scratchthelens,especiallyifthesurfaceisdusty.NEVERcleanthelightwithcleaninguidorsolvent.

3.DONOTattempttocleantheinsideofthelightortouchtheinsidelensandreector.

4. LIGHTFORCElightsarenotdesignedtobeusedforlongperiodsoftimeinastationarypositionwithminimalairow,failureto 

comply will void warranty. Contact LIGHTFORCE direct to discuss alternative options such as reducing globe wattage.

5.GLOBEREPLACEMENT:TheXenophot®globegivesapproximately10%greaterefciencythananyotherhalogenglobeofsimilar

voltage. A number of optional globe strengths are available upon request. For removal, simply:

  a)Rotatethereectorhousinganti-clockwisetodisengageit.

  b)Removeoldglobebygrippingrmlyandpullingoutinthelongaxisdirectionoftheglobe.

i) DO NOT TOUCH NEW GLOBE WITH FINGERS, use a tissue or plastic sleeve. Prior to inserting a new globe, scrape the

 globelegswithanabrasivesurface(sandpaperorknifeedge)toensurepositivecontactwiththeglobeholderelectrodes. 

 ii)Positiontheglobelegsrmlyintothexedelectrodesoftheglobeholder,applyingarmpressuretowardstherear.AVOID 

 jerkingortwistingmovements.NOTE:GlobecanonlybemovedtotheleftandrightNOTupanddown.   

 iii)Mereplacementoftheglobeintotheglobeholderisoftennotsufcienttogiveaproperlynetunedbeam.Theoperator 

 canovercomethisbyaligningthesplitlinealongthetopoftherotationlockingNIBandthesplitlineontheendofthe  

 handlewiththecentreoftheglobelament.(seeFig.1)        

v) All other globes should be seated against the globe holder with little or no air gap.

vi) Maximum globe wattage recommendation:

140 LANCE: 12V 75W

170 STRIKER: 12V 100W

240 BLITZ: 12V 100W

Note: USING GREATER WATTAGE WILL VOID WARRANTY

6. FOCUSING MECHANISM: The patented focus mechanism allows precise adjustment of the beam to various concentration patterns as

desired.SimplyrotatethereectorandselectthedesiredSPOT.

7.Ensurethatduringusethereectorsurfaceisnotwoundtoofarforwardpasttheglobeholderormeltingofthehousingcanoccurand

will not be covered under warranty.

8. We recommend wiring remote mount driving lights with a minimum 10 amp wire.

9. Tools needed for installation are

• 17mmsocketonratchetx2orequivalent

• Torque wrench

10.YourHIDlightcanbemountedwiththebottommountbracketttedineitherdirection(i.e.rotated180degrees).Ifyoundthat

youneedtomountyourlightlowerthenour‘lowmount’bracketcanbepurchased(partnumber#MVDL).Thiscanalsobeturned

180 degrees for a greater offset than the standard ‘high mount’.

11.Determinesuitablemountingpositionandtlightintoposition.

12.Aimlight(i.e.pointstraightahead)thentightenbothboltsasperrecommendedtorquespecications(seespecicationsbelow).

13.MountingfastenertorquespecicationsareallM10bolts-70Nm(50lb-ft).

LIGHTFORCEAUSTRALIAPTYLTD•28OrsmondStreet,HindmarshSA5007Australia•www.lightforce.com|email:[email protected]

Australia:Tel:0884400888|Fax:0883460504•Int’l:Tel:+61884400888|Fax:+61883460504

AlllogosandimagesaresubjecttorelevanttrademarkandcopyrightprotectionLIGHTFORCEPtyLtd|©March2013•Dataandspecicationscontainedmaybesubjecttochangewithoutnotice.

LIGHTFORCEAUSTRALIAPty.Ltd.,shallbenotbeliablefordamage,malfunction,failureresultingfromaccident,misuse,misapplication,unauthorisedrepair,neglect,modication,unauthorisedornonstandardreplacementparts,accessories,

globes,batteriesorvoltageortheoperationoftheProductbeyonditstechnicalandenvironmentalspecications.

INSTRUCTION DATA

PRODUCT: REMOTE MOUNT DL

VER: 1.0

DATE: MARCH 2013

Fig.2

Fig.1

INSTRUCTION DATA 1

Inhaltsverzeichnis

Seite 1 - INSTRUCTION DATA

1. Ensure all electrical connectors are secure; loose connections will generate excessive heat, damage wiring and causing electrical failure.

Kommentare zu diesen Handbüchern

Keine Kommentare

Lightforce 240 BLITZ REMOTE MOUNT DL Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Beleuchtung Lightforce 240 BLITZ REMOTE MOUNT DL herunter. Lightforce 240 BLITZ REMOTE MOUNT DL User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Beleuchtung Lightforce 240 BLITZ REMOTE MOUNT DL